ShopFloorJobs
Eaton logo

Sr Process Engineer - Heat Treat / Fabrication

Eaton · Orchard Park, NY

Level
Level: Senior
Team
Team: Process
Base pay
Base pay: $97k–$143k
Experience asked
Experience asked: 3+ years
Industry
Industry: Industrial
Posted
Posted: 19 days ago
Apply on Eaton ↗

The role in 30 seconds

A senior process role at Eaton (industrial) in Orchard Park, NY. Develop, qualify, and improve manufacturing methods, fixtures, and tooling to improve quality, throughput, and cost.

They ask for
3+ years
Tools it names
Lean, Root cause, FMEA, Control plans, Validation (IQ/OQ/PQ), Capacity planning
Base pay
$97k–$143k

Read from the posting. The full description is below.

From the plant jobs report · week of November 16, 2026

Process Engineer roles in New York: typical posted base $95k–$134k. This one lists $97k–$143k.

Median of the low and high ends of 33 live postings that list pay, out of 45 process engineer openings in New York, read from manufacturers' own careers sites.

New York plant jobs report →Pay by team and state →What moves pay →

How this role compares

Against 44 other live process postings in New York.

Base pay
About 5% above similar roles

Typical $95k–$134k, from 32 postings that list pay.

Experience asked
Less than usual (3+ vs 5+)

Similar roles usually ask 5+ years.

Skills these teams ask for most

  • ✓ Root cause 56%
  • DOE 44%
  • ✓ Lean 42%
  • SPC 42%
  • Six Sigma 27%
  • ✓ Tooling 24%

✓ = this posting asks for it too. % = share of similar postings that mention it.

Stands out: this posting asks for FMEA, Control plans, Capacity planning, which few similar roles mention. If you have it, lead with it.

It asks for 3+ years. If you're close, apply anyway: requirements are a wish list. Talk to someone doing this work there first.

At a glance

Pulled from the posting text. If it's not listed here, the posting didn't say.

How to get in at this plant

Five moves over a week or two. The first one takes ten minutes.

  1. 1

    Pick 2–3 people on the Process team at Eaton

    Engineers who joined in the last year or two reply the most. Use the team search on this page to find them.

  2. 2

    Send a short, curious note

    One real question about their work. No favors yet. Each person gets a different note, written for this role.

  3. 3

    Turn a reply into a short call

    Questions worth asking about this team:

    • What does a normal week look like on your team?
    • Is the work mostly new product launches or sustaining existing lines?
    • How much time do you spend on the floor versus at a desk?
    • How did you land the job? What stood out in your interviews?
  4. 4

    Apply with someone vouching for you

    If the call went well, ask whether they’d pass your résumé to the hiring manager. Send your résumé link, apply that day, and let them know.

  5. 5

    Bring proof to the interview

    One page of before-and-after numbers from projects you led: scrap, OEE, cycle time, cost. Plant managers hire on results.

This plant: Eaton in Orchard Park

8 other open roles at this site.

All 9 roles at Eaton →
Full description from EatonAs posted on their careers site.Show

Responsibilities

  • ◆Work safely at all times and follow all Eaton MESH protocols, including risk assessments, lockout/tagout, hot work, and chemical handling requirements, and ensure processes, equipment, and work instructions meet MESH, machine guarding, and environmental

requirements

before release to production.

  • ✓Own manufacturing processes, routings, work instructions, and standard work for assigned product families, and keep that documentation current as processes change.
  • ✓Develop, qualify, and improve manufacturing methods, fixtures, and tooling to improve quality, throughput, and cost.
  • ✓Lead root cause analysis and corrective action on scrap, rework, and process-related quality escapes using structured problem solving.
  • ✓Support new product introduction through process design, PFMEA, control plans, and process capability studies.
  • ✓Drive lean and continuous improvement activity on the floor, including cycle time reduction and capacity planning.
  • ✓Serve as the site subject matter expert for heat treat: understand furnace and oven behavior, atmosphere and quench media control, fixturing, and load design, and be able to run the equipment personally.
  • ✓Program and maintain heat treat oven and furnace recipes and controllers, including setpoints, ramp and soak profiles, alarms, and recipe change control.
  • ✓Work safely at all times and follow all Eaton MESH protocols, including risk assessments, lockout/tagout, hot work, and chemical handling requirements, and ensure processes, equipment, and work instructions meet MESH, machine guarding, and environmental

requirements

before release to production.

  • ✓Own manufacturing processes, routings, work instructions, and standard work for assigned product families, and keep that documentation current as processes change.
  • ✓Develop, qualify, and improve manufacturing methods, fixtures, and tooling to improve quality, throughput, and cost.
  • ✓Lead root cause analysis and corrective action on scrap, rework, and process-related quality escapes using structured problem solving.
  • ✓Support new product introduction through process design, PFMEA, control plans, and process capability studies.

Job

Responsibilities

  • ◆Drive lean and continuous improvement activity on the floor, including cycle time reduction and capacity planning.
  • ◆Serve as the site subject matter expert for heat treat: understand furnace and oven behavior, atmosphere and quench media control, fixturing, and load design, and be able to run the equipment personally. This applies for the spring manufacturing, lapping processes and soldering as well.
  • ◆Program and maintain heat treat oven and furnace recipes and controllers, including setpoints, ramp and soak profiles, alarms, and recipe change control.
  • ◆Validate heat treat processes end to end — temperature uniformity surveys, system accuracy tests, instrumentation calibration, thermocouple management, and load qualification — and maintain the supporting records.
  • ◆Develop and approve heat treat specifications and process sheets, and confirm results through metallurgical evaluation such as hardness, case depth, microstructure, and distortion.
  • ◆Keep special process documentation audit-ready and support internal, customer, and third-party audits.
  • ◆Troubleshoot equipment and process issues with maintenance and controls, and drive preventive maintenance

requirements

for heat treat assets.

  • ✓Support the spring room: coiling and forming parameters, stress relief and setting operations, material selection, load and rate verification, and tooling.
  • ✓Support the lapping room: lapping and finishing process parameters, abrasive and media selection, machine setup, flatness and surface finish control, and consumable qualification.
  • ✓Identify, justify, and lead capital projects for heat treat, fabrication, and finishing equipment, lapping, spring room, including scope definition, payback analysis, and appropriation requests.
  • ✓Own capital project schedule and budget, and close each project out with validated process capability, trained operators, and complete documentation.
  • ✓Partner with quality, maintenance, production supervision, and suppliers to sustain process performance and equipment uptime.
  • ✓Validate heat treat processes end to end — temperature uniformity surveys, system accuracy tests, instrumentation calibration, thermocouple management, and load qualification — and maintain the supporting records.
Show full description ↓

Eaton’s IS AER MSD division is currently seeking a Sr Process Engineer - Heat Treat / Fabrication. This role is based in Orchard Park, NY.

Please note the salary information shown above is a general guideline only. Salaries are based upon candidate skills, experience, and qualifications, as well as market and business considerations.

What you’ll do

Eaton's Aerospace Group, Mission Systems Division (MSD) is seeking a Sr Process Engineer who will be the technical owner of heat treat , spring manufacturing, lapping and soldering at the Orchard Park facility. This role combines the full scope of a manufacturing engineer — process development, tooling, capability studies, cost and throughput improvement — with deep, hands-on ownership of the plant's special process areas listed above. The engineer is accountable for the day-to-day operation, programming, and validation of related equipment, and provides direct engineering support to the heat treat, spring room, lapping and solder operations. Other related fabrication areas could be added as the business grows.

This is a floor-facing position. Success depends on being present at the equipment, understanding metallurgical response as well as machine behavior, and translating that understanding into repeatable, documented, audit-ready processes. The engineer also leads capital projects that modernize and expand special process capability at the site.

Job

More Process roles nearby