Manufacturing Engineer
DG Matrix · Morrisville, NC
- Level
- Level: Engineer
- Team
- Team: Manufacturing
- Degree
- Degree: Required
- Experience asked
- Experience asked: 3+ years
- Industry
- Industry: Industrial
- Posted
- Posted: Recently
The role in 30 seconds
An engineer-level manufacturing role at DG Matrix (industrial) in Morrisville, NC. Develop, document, and continuously improve manufacturing processes, work instructions, and BOMs for power electronics products.
- They ask for
- 3+ years · degree required
- Tools it names
- Lean, 5S, Root cause, FMEA, Control plans, Validation (IQ/OQ/PQ)
- Day to day
- some off-shift / weekend coverage · relocation help
Read from the posting. The full description is below.
From the plant jobs report · week of November 16, 2026
Manufacturing Engineer roles in North Carolina: typical posted base $97k–$143k.
Median of the low and high ends of 18 live postings that list pay, out of 62 manufacturing engineer openings in North Carolina, read from manufacturers' own careers sites.
North Carolina plant jobs report →Pay by team and state →What moves pay →
How this role compares
Against 61 other live manufacturing postings in North Carolina.
- Base pay
- Not listed in this posting
- Experience asked
- Less than usual (3+ vs 5+)
Typical $97k–$143k, from 16 postings that list pay.
Similar roles usually ask 5+ years.
Skills these teams ask for most
- ✓ Tooling 48%
- ✓ Lean 47%
- ✓ New product launch 39%
- Six Sigma 27%
- ✓ Validation (IQ/OQ/PQ) 27%
- ✓ Root cause 26%
✓ = this posting asks for it too. % = share of similar postings that mention it.
Stands out: this posting asks for 5S, Time studies, SolidWorks, which few similar roles mention. If you have it, lead with it.
At a glance
Pulled from the posting text. If it's not listed here, the posting didn't say.
How to get in at this plant
Five moves over a week or two. The first one takes ten minutes.
- 1
Pick 2–3 people on the Manufacturing team at DG Matrix
Engineers who joined in the last year or two reply the most. Use the team search on this page to find them.
- 2
Send a short, curious note
One real question about their work. No favors yet. Each person gets a different note, written for this role.
- 3
Turn a reply into a short call
Questions worth asking about this team:
- What does a normal week look like on your team?
- Is the work mostly new product launches or sustaining existing lines?
- How much time do you spend on the floor versus at a desk?
- How does off-shift and weekend coverage work?
- How did you land the job? What stood out in your interviews?
- 4
Apply with someone vouching for you
If the call went well, ask whether they’d pass your résumé to the hiring manager. Send your résumé link, apply that day, and let them know.
- 5
Bring proof to the interview
One page of before-and-after numbers from projects you led: scrap, OEE, cycle time, cost. Plant managers hire on results.
Full description from DG MatrixAs posted on their careers site.ShowHide
About the Role
DG Matrix is seeking a Manufacturing Engineer to support the ramp-up of our new facility in Morrisville, NC. This is a ground-floor role — you will build manufacturing processes from scratch, translate engineering designs into production-ready work instructions, and own process quality for power electronics products as we scale from first unit to hundreds per year. If you are energized by ambiguity and building from scratch, this role is for you.
Key Responsibilities
- ◆Develop, document, and continuously improve manufacturing processes, work instructions, and BOMs for power electronics products
- ◆Lead NPI (New Product Introduction) — translate engineering designs into production-ready processes and tooling
requirements
- ✓Define and optimize work cell layouts, cycle times, takt time, and line balancing across production phases
- ✓Own process FMEA (PFMEA) and control plans for assigned product lines
- ✓Drive root cause analysis and corrective action (8D, Fishbone, 5-Why) for production non-conformances
- ✓Collaborate with Design Engineering on DFM (Design for Manufacturability) improvements
- ✓Support MES/ERP implementation and ensure accurate process data capture on the shop floor
- ✓Track and report yield, throughput, and cycle time KPIs; define and drive improvement actions
- ✓Support equipment procurement, qualification, and process validation for new work cells
- ✓Interface with suppliers on component quality, incoming inspection criteria, and delivery issues
Required Qualifications
- ✓Bachelor's degree in Mechanical, Electrical, or Manufacturing Engineering
- ✓3+ years of manufacturing engineering experience in electronics, power systems, or industrial equipment
- ✓Strong working knowledge of Lean Manufacturing, 5S, and continuous improvement methodologies
- ✓Experience with PFMEA, control plans, and structured problem-solving (8D, 5-Why)
- ✓Proficiency with CAD tools (SolidWorks preferred) and MS Office / Google Suite
- ✓Experience with MES or ERP systems (Odoo, SAP, or similar)
- ✓Strong cross-functional communication — design, quality, supply chain, and operations teams
Preferred Qualifications
- ✓Experience in power electronics, inverters, EV, energy storage, or grid infrastructure manufacturing
- ✓Familiarity with UL, IEC, or NFPA standards for power equipment
- ✓Experience scaling production from low-volume to higher-volume manufacturing
- ✓Knowledge of high-voltage assembly and test processes for 3-phase systems
Why Dg Matrix
Rare opportunity to shape manufacturing from the ground up at a fast-growing clean energy company. High ownership, direct leadership visibility, and a collaborative engineering team. Your work directly determines how DG Matrix scales its power electronics platform.
